How To Set Drag On Reel

Download Article

Download Article

If you've been fishing for a while, you know how frustrating it is to lose a big fish to a cleaved line. This normally happens when the drag, the device which sets how much resistance a fish feels when it pulls on the line, isn't set properly. Fortunately, there's an easy solution for adjusting the drag. One time you lot learn nigh your specific reel and drag adjuster, cheque the resistance, and make the necessary corrections. And then get out and grab the one that got abroad!

1. 

   1

   Determine what kind of reel you use. There are three basic types of reels that contain your line. This commodity won't get into the pros and cons of each; instead, it's important that yous know what kind you have and where the drag adjustment is located.

   • Spincasting reels are airtight face. Your line will be encased past a cone-like cover and the line feeds out of a small pigsty in it.^[ane]
   • Spinning reels are open-faced. Your line spool will be exposed and you lot'll be able to lookout it spin out. This one looks the most exposed.^[2]
   • Baitcasting reels await like a mix between an open- and closed-confront reel. The most noticeable feature is that the whole line spool volition turn when you cast the line.^[3]

2. 

   ii

   Locate your drag adjustment. Now that you know what kind of reel you're using, acquire where the drag adjustment is located on your reel.

   • The spincast'due south drag aligning is commonly next to the reel handle. Information technology looks somewhat like a star-shaped knob and may click as you play with the drag. This allows you to hear simply how much yous're adjusting.
   • The spinning reel'south elevate adjustment is a circular knob facing out at the front of your line spool.
   • The baitcaster'southward drag adjustment looks similar a star and is located next to the reel handle. Turning it clockwise volition tighten information technology and counter-clockwise loosens the drag.

   Advertisement

3. 

   iii

   Learn the breaking strength for your line. Wait on the bundle your line came in. It should conspicuously state in pounds how much resistance your line can handle without breaking.

   • This will tell you what your optimum drag should be. Elevate should always exist no more than 25 percent of your your breaking strength's resistance. To effigy drag, simply divide your breaking strength by 4. The result is what your drag should be set at.^[4]

4. 

   4

   Get a calibration. At present that you know what your elevate should be, y'all'll need to see where your elevate is currently set.

   • Yous can use a digital scale or a spring scale (such as the sort used to counterbalance fish). Both have a hook at the end to which you adhere your line.

Advertizing

1. 

   one

   Get together your rod. Prepare upward your rod and thread the line as though you are going to actually utilize the rod. Be certain to thread the line through all of the guides in society to get an authentic reading.

2. 

   2

   Necktie your line to the scale. You'll need to necktie information technology securely to the hook at the end of your digital or bound scale. Make certain the line tin can't slip off when the scale is pulled.

3. 

   3

   Position your rod. Hold the rod at a 45 degree angle. Information technology's useful to have a friend hold your rod or the scale. Keep the scale vertical so that the hook and line are at the top.

4. 

   4

   Pull downwardly on the scale. At first, your line won't exercise anything other than curve down with the weight. And so, y'all should notice the drag kickoff to slip and the line extend. Every bit soon every bit this happens, expect at the scale and take a measurement.

5. 

   5

   Adjust your elevate. Wait at where your drag is and what information technology should be set at. Apply the drag adjustment knob on your reel and tighten or loosen as needed. Bank check the drag on a scale.

Advertisement

Add together New Question

• Question

  What do I do if my fishing line is all wrinkled?

  

  The line is wrinkled or loopy, information technology may exist because the line has been sitting on the reel for a long time and should be replaced. Newer line may exist loopy when you first utilise it. To avert loops in your reel, retrieve the line slowly while holding it firmly between your fingers until the line is tight. Once all the slack has been retrieved, let become of the line and retrieve your lure/allurement ordinarily.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Ad

Video

• If you're using a leader, test the drag for whichever has a lower breaking strength: your leader or your line.^[5]

Thanks for submitting a tip for review!

Advertisement

About This Article

Article Summary X

Setting the drag properly on your fishing reel will assistance you keep your fish on the line without snapping it. To set i, first, yous'll need to assemble your rod and thread the line. Tie the end of your line to a scale, then concord your rod at a 45-degree angle. Have a friend pull downward on the scale slowly. One time the elevate starts to slip and the line extends, look at the scale and take down the measurement. And so, utilise the drag adjustment knob to tighten or loosen it to what yous demand. In general, the elevate should be no more 25 percent of your breaking force'due south resistance. If you don't know this number, look on the packet your line came in, which should say how much resistance your line can handle. To learn how to locate your drag adjustment knob, read on!

Did this summary assistance you?

Thank you to all authors for creating a folio that has been read 66,409 times.

Did this article help y'all?

Source: https://www.wikihow.com/Set-the-Drag-on-a-Fishing-Reel

Share this post